企业信息

    济宁市天通机械设备有限公司

  • 9
  • 公司认证: 营业执照已认证
  • 企业性质:有限责任公司
    成立时间:
  • 公司地址: 山东省 济宁 任城区 唐口街道 唐口工业园
  • 姓名: 范先生
  • 认证: 手机已认证 身份证已认证 微信未绑定

    供应分类

    吉林 废水处理设备 雨水处理 电解式 哪家强

  • 所属行业:环保 水处理设备 污水处理成套设备
  • 发布日期:2017-12-29
  • 阅读量:122
  • 价格:面议
  • 产品规格:定制
  • 产品数量:1500.00 台
  • 包装说明:定制
  • 发货地址:山东济宁任城区唐口街道  
  • 关键词:废水处理设备,雨水处理,环保水处理

    吉林 废水处理设备 雨水处理 电解式 哪家强详细内容

    公司简介:济宁天通水处理设备有限公司是一家集研发、制造、销售为一体,是一家实力雄厚的水处理设备公司。公司主营综合环境服务,包括大型企业,工业废水零排放,园区项目;投资、建设和危险废物综合利用综合**手术;环境工程;环保设备;水处理设备;膜处理设备。具备环境工程设计资质、污水处理设施经营资质和危险废物处置资质。
     带式压滤机
    
    压滤机是在过滤介质一侧施加机械力实现过滤的机械,主要用于污泥(水)的固液分离。而污泥压滤机大多用在造纸、淀粉、酒精、维C工程等行业的工业污泥脱水。
    
    一、工作原理
    含水污泥,经污泥泵输送至污泥搅拌罐,同时投加凝聚剂进行充分混合反应,而后流 入带式污泥压布泥器,污泥均匀分布到重力脱水区上,并在泥耙的双向疏导和重力作用下,污泥随着脱水滤带的移动,迅速脱去污泥的游离水。由于重力脱水区设计较长,从而达到较大限度重力脱水。翻转下来的污泥进入**长的楔形预压脱水区将重力区卸下的污泥缓缓夹住,形成三明治式的夹角层,对其进行顺序缓慢预增加压过滤,使泥层中的残余游离水份减至较低,随着上下两条滤带缓慢前进,两条滤带之间的上下距离逐渐减小,中间的泥层逐渐变硬,通过预压脱水大直径的过滤辊,,将大量的游离水脱掉,为泥饼  污泥压滤机
      顺利进入挤压脱水区,进入“ S ”压榨段,在“ S ”型压榨段中,污泥被夹在上、下两层滤布中间,经若干个压榨辊反复压榨,上下两条滤带在经过交错各辊形成的波形路径时, 由于两条滤带的上下位置顺序交替,对夹持的泥饼产生剪切力, 将残存于污泥中的水分绝大部分积压滤除,促使泥饼再一次脱水,最后通过刮刀将干泥饼刮落,由皮带输送机或无轴螺旋输送机运至污泥存放处。
    
    二、性能优点
    
    1. 滤带自动涨紧、自动纠偏,彻底解决滤带跑偏损坏滤带问题;电控系统设有连锁保护装置,确保整机运行的安全可靠。   
    2. 采用多种防腐手段防腐,使用寿命长;  
    3. 三重脱水区**长设计,脱水率高,泥饼含固率高;   
    4. 原理简单,部件统一,易于管理,维修方便;   
    5. 运转平稳,噪音低,化学药剂用量少;   
    6、 转速快,调偏快,产量大
    
    三、制造优点
    1、 主机机架方钢焊接增加坚固度,热镀锌防腐处理抗酸、碱腐蚀,保用五年。   
    2、 主机所有包胶辊密封包胶,防腐彻底。   
    3、 接水盘使用不锈钢,坚固耐用。   
    4、 系统运行费用、维护费用较同类产品大幅降低。   
    5、 污泥处理量高,滤饼含水率低于同类产品。
    四、应用范围
    该带式压滤机适用于城市污水处理厂、制药、电镀、造纸、皮革、印染、冶金、化工、屠宰、食品、酿酒及环保工程中废水处理工序的污泥脱水,在工业生产中也可用于固液分离之场合,是环境治理和资源回收的理想设备。也可以应用于工业生产中的固液分离或液体浸出工序。在国内环保工程项目上得到广泛使用。
    五、操作程序
    1、准备工作
    (1)请详细读本说明书,并了解所述之操作程序及方法,以熟练操作脱水机及其组成之元件。   
    (2)检查污泥压滤机及其元件是否全在良好状态,并确认无其它杂物残存在滤布及滚轮上。   
    (3)检查减速机油液。   
    (4)检查滤布位置是否正确。   
    (5)检查刮板是否与滤布适当接触。
    (6)检查上、下滤布的张力是否适当,并将之调整为适当的张力。   
    (7)检查空压机及调整器的空气压力。
    2、开始工作
    
    (1)启动空压机空气贮槽的控制阀,将加压空气送入气压控制单元。   
    (2)调整气压以设定滤布张力,预调整时,注意张力伸缩架不能触碰到机架。   
    (3)用手稍微的搬动滤布偏移感应装置,检测气缸是否会正常动作。另外,试验紧急停止开关功能是否正常。   
    (4)启动滤布洗涤泵,并检视泵的水量及水压是否符合要求(水压:4kg/cm2)。   
    (5)接着启动污泥脱水机并检查是否所有设备都正常运转。   
    (6)启动污泥供应泵。   
    注意: (1)如果滤布偏移不能回复正常位置时,请立即停止运转。  
    (2)切记如果滤布上的张力未能适当保持时,滤布偏移控制系统则可能不能发挥其功能。
    3、停止工作
    (1)关闭污泥供应泵。   
    (2)接着,让污泥压滤机运转至少20分钟,在污泥压滤机还运转时,滤布洗涤泵及污泥输送装置亦需继续维持运转,直到残余污泥能完全脱离污泥压滤机并洗净滤布。  (3)在确定污泥饼完全脱离污泥压滤机,滤布及滚轮都被洗净后,再关掉污泥压滤机、洗涤泵及污泥饼输送装置。   注意:当停止操作后,如果有一段较长的时间不操作污泥压滤机,则请放松滤布的张力。(在要重新开机运转前,请勿忘记先调整好滤布的张力。)
    六、污泥压滤机的保养
    
    (1)机电部分
    1、注意清洗泵和泥浆是否有油,地脚螺丝是否松动。   
    2、检查污泥搅拌机、药搅拌机、带式污泥脱水机的减速机内是否**械润滑油,螺丝是否有松动。   
    3、空压机和输送带的传动部分要定期加油,保持油面、空压机的贮气罐内每天放水一次。   
    4、开车前检查行程开关和电磁阀是否损坏,如有应及时更换。
    
    (2)气动部分
    
    1、注意压缩空气管,不能接触火星和挤压。   
    2、控制箱内的油杯、油位应保持液面,并三个月换油一次,才能确保气罐正常工作。
    
    (3)传动部分
    
    1、调速电机的传动链条,每月加黄油一次,保持正常运行。   
    2、脱水机所有轴承每月用黄油枪加油一次。   
    3、调偏和张紧的中心轴的轴承应三个月加黄油一次。   
    4、所有调偏和张紧滑块,要保证不生锈,每星期用机油枪加油一次,保证润滑、灵活。   
    5、污泥处理系统所有紧固件、轴承外壳6、每月涂黄油一次,保证零件不给污水、污泥及空气腐蚀。
    Company profile: Jining Tian Tong water treatment equipment Co., Ltd. is a R & D, manufacturing and sales company, and is a strong water treatment equipment company. The company is mainly engaged in comprehensive environmental services, including large enterprises, industrial wastewater zero discharge, park project, investment, construction and comprehensive utilization of hazardous waste comprehensive treatment operation; environmental engineering; environmental protection equipment; water treatment equipment; membrane treatment equipment. Qualification of environmental engineering design, *age treatment facilities management and hazardous waste disposal.
    belt pressure filter
    
    Filter press is a machine that applies mechanical force on one side of the filter medium to realize filtration. It is mainly used for solid-liquid separation of sludge (water). The sludge press is mostly used in the dewatering of industrial sludge in papermaking, starch, alcohol, vitamin C and other industries.
    
    1. Working principle
    Water sludge by sludge pump conveying to the sludge mixing tank, adding coagulant for mixing reaction, and then into the belt type sludge cloth pressing mud cleaner, sludge evenly to gravity dewatering zone, and the mud rake two-way grooming and gravity, with the mobile sludge dewatering belt filter, rapid removal of free water sludge. The gravity dehydration zone is designed to achieve maximum gravity dehydration as a result of the long design of the gravity dehydration zone. Wedge pre flip down sludge into long pressure dewatering zone will remove the sludge gravity zone slowly can form an angle of sandwich type, the order of the slow advance by pressure filtration, the mud layer of residual free water to a minimum, with the two filter with slow progress, two filter belts between the upper and lower distance decreases, mud in the middle layer hard gradually, through the filtering roller, pre pressure dehydration of large diameter, the amount of free water off, as the mud cake sludge filter press
    Enter the extrusion dehydration, into the "S" press, press the "S" section, the sludge is caught in the middle, two layers of cloth, after several repeated press roll press, two upper and lower filter belt after each roll forming path of staggered waveform, because two up and down position order filter with alternating shear force generated on mud cake clamping, will remain in the sludge water in most of the backlog of filter cake, make again dehydration, finally the scraper will dry mud cake is scraped by belt conveyor or screw conveyor transport to the sludge storage.
    
    Two. Performance advantages
    
    1., the filter belt is automatically tightened and automatically rectify. It solves the problem of filter belt deviation and damage filter completely, and the electric control system has a chain protection device to ensure the safety and reliability of the whole machine operation.
    2. a variety of anticorrosive methods are used for anticorrosion and long service life.
    3. three heavy desiccation area is super long design, the dehydration rate is high, the mud cake has a high solid content.
    The 4. principle is simple, the components are unified, easy to manage and easy to repair.
    5. smooth operation, low noise, less chemical dosage;
    6. Fast speed, fast adjustment and large output
    
    Three. Advantages of manufacturing
    1, the host machine increase square steel welding firmness of hot galvanizing anticorrosion treatment of acid and alkali corrosion, guaranteed for five years.
    2, all the mainframe rubber rolls seal the adhesive, and the anticorrosion is thorough.
    3, the water plate used stainless steel, sturdy and durable.
    4, the operating costs and maintenance costs of the system are significantly lower than those of the same kind.
    5, the amount of sludge treatment is high, and the water content of the filter cake is lower than that of the same kind.
    Four. Application scope
    The belt type filter press is suitable for sludge dewatering wastewater treatment process of city *age treatment plant, pharmaceutical, electroplating, paper, leather, printing and dyeing, metallurgy, chemical, food, brewing and slaughtering, environmental engineering, industrial production also can be used for solid-liquid separation, is the ideal equipment for environmental governance and resource recovery. It can also be used in the process of solid liquid separation or liquid leaching in industrial production. It has been widely used in domestic environmental protection projects.
    Five. Operation program
    1. Preparation for work
    (1) please read the instructions in detail and understand the operating procedures and methods described in order to manipulate the dehydrator and its components.
    (2) check whether the sludge filter press and its components are in good condition, and confirm that no other debris remains on the filter cloth and roller.
    (3) check the deceleration oil.
    (4) check the position of the filter cloth correctly.
    (5) check whether the scraper is in proper contact with the filter cloth.
    (6) check the tension of the upper and lower filter cloth and adjust it to the appropriate tension.
    (7) check the air pressure of the air compressor and the regulator.
    2. Start work
    
    (1) start the control valve of the air tank of the air compressor and send the pressurized air into the air pressure control unit.
    (2) adjust the pressure to set the tension of the filter cloth, when the pre adjustment, the tension telescopic frame can not touch the frame.
    (3) use the hand to move the filter cloth to offset the induction device to detect the normal movement of the cylinder. In addition, the test emergency stop switch function is normal.
    (4) start the filter cloth washing pump, and check whether the water and water pressure of the pump meet the requirements (water pressure: 4kg/cm2).
    (5) then start the sludge dehydrator and check whether all the equipment is working properly.
    (6) start the sludge supply pump.
    Note: (1) if the filter offset can not return to the normal position, please stop the operation immediately.
    (2) remember that if the tension on the filter is not properly maintained, the filter offset control system may not be able to perform its function.
    3. Stop work
    (1) shut down the sludge supply pump.
    (2) next, let the sludge filter press run for at least 20 minutes. When the sludge filter press is running, the filter cloth washing pump and sludge conveying device must continue to operate until the sludge filter is running.

    http://jnttjx01.cn.b2b168.com
    欢迎来到济宁市天通机械设备有限公司网站, 具体地址是山东省济宁任城区唐口工业园,老板是尹宜良。 主要经营济宁 天通,是国内成员之一的机械设备加工生产研发厂家,其核心技术以:智能自动化小型压路机、数控钢筋笼滚焊机、公路拌合机机械设备为主。 济宁 天通,始终坚持以“先做人,后做事”为核心价值观,以“儒商文化”为品牌文化,以“做今日品牌,创**企业”为宗旨,以“实用为本、德行天下”为理念,铸造中国机械行业的**品牌。公司依托与国外的分支机构、国内的办事处、及专业的施工队伍,凭借行业内设备研发*团队的强大创。 单位注册资金单位注册资金人民币 100 - 250 万元。 我司专营小型压路机,灰土拌和机,拖拽式小宝马拌和机,手扶压路机,钢筋笼滚焊机,研发团队成员,均来自国内外大型工程机械企业的研发机构的专业技术人员。经过多年的实践与积累,掌握了多种工程机械产品从设计到生产加工的全套技术。